شرایط اتاقک دستگاه کلرزن در تصفیه آب
۱٫ دستگاه را از باران وتابش مستقیم خورشید ، سرما و گرما محافظت نماید .
۲٫ دارای تهویه مناسب ، روشنایی کافی ، کفشور (حهت شستشوی دستگاه ) و برق (برحسب نوع دستگاه برق تک و یا سه فاز) باشد .
۳٫ نزدیک مکان تزریق کلر و در صورت ممکن بر روی لوله آب ساخته شود1. مخزن همزن را تا بیست سانتی متری دهانه ، از آب پر نمایید .
۲٫ به مقدار لازم پودر کلر را در داخل آن بریزید .
۳٫ همزن را روشن کرده اجازه دهید ۲ الی ۱۰ دقیقه محلول همزده شود سپس همزن را خاموش نمایید .
۴٫ حداقل ده دقیقه اجازه دهید تا آهک تشکیل شده رسوب نماید .
۵٫ در دستگاههای تک مخزنه محلول آماده تزریق میباشد .
۶٫ در دستگاههای دو مخزنه با باز کردن شیر واسط ، محلول در مخزن تزریق پر شده و قابل استفاده میباشد .
نصب دستگاه :
۱٫ دستگاه ، در مکانی با شرایط فوق قرار داده شود .
۲٫ برق دستگاه به برق شهر و برق پمپ چاه وصل گردد .(فرمان پمپ تزریق بهتر است از پمپ چاه تغذیه شود. )
۳٫ به لوله آب یک بوشن ۴/۳ وصل گردیده و سپس انژکتور تزریق به آن بسته شود .
۴٫ یک شیر جهت تامین آب دستگاه به نزدیکی دهانه مخزن کشیده شود .
نگهداری دستگاه کلرزن مایع :
۱٫ مخزن دستگاه حداقل هر هفته یکبار تمیز گردد.
۲٫ حداقل هر ماه یکبار دستگاه سرکه شویی گردد.(یک لیوان سرکه توسط پمپ مکش شده سپس ۱۰ دقیقه در داخل پمپ و مسیر تزریق بماند تا رسوبات را پاک نماید )
۳٫ از وارد آوردن ضربه به قسمتهای مختلف دستگاه به خصوص انژکتورها و میله همزن خودداری گردد.
۴٫ پیچ دبی را فقط در حالتی که دستگاه روشن میباشد تنظیم نمایید.
۵٫ ظاهر دستگاه را حداقل هفته ای یکبار تمیز نمایید.
۶٫ در صورت وجود رسوبات بر روی دستگاه بخصوص هد و انژکتورها آن را با سرکه و یا اسید شستشو بدهید.
۷٫ در صورتی که دستگاه بیشتر از یک روز از سرویس خارج میگردد باید سرکه شویی شود.
1. The machine from rain and direct sunlight, protect from cold and heat.
2. Has adequate ventilation, adequate lighting, Kfshvr (trying to washing machine) and electricity (depending on single or three-phase electrical device) is.
3. Near chlorine injection and may be built on a water pipe 1. Twenty-inch hopper tank has openings, fill with water.
2. The necessary amount of chlorine powder into the fold.
3. Turn on the mixer Let stirred solution of 2 to 10 minutes, then turn off the mixer.
4. At least ten minutes to let the limestone deposits.
5. In the single-reservoir system solution is ready for injection.
6. In the two-reservoir system by opening the valve interface solution and is used in high pressure pot.
Installation:
1. Device with the above conditions be put in place.
2. Power is connected to AC power downhole pump. (Command injection pump should be fed from the pump well.)
3. To pipe a 4/3 plug socket and then injected into the injector is closed.
4. A valve near the mouth of the reservoir to supply water to be drawn.
Maintenance liquid Drumsticks:
1. Tank cleaned at least once a week.
2. At least once a month cleaning device is vinegar. (A glass of wine by the suction pump inside the pump and the injection and then 10 minutes until the clean sediments)
3. From blows to various parts of the injectors and stirring rod to be avoided.
4. Screw Dubai is only set when the power is turned on.
5. The appearance of the device at least once a week clean.
6. In the case of deposits on the injector device and especially its head with vinegar or acid wash manager.
7. If the device is out of service for more than a day should be cleaning vinegar
Domestic water purifier in Karaj, water purifier relax, chlorinator pump water with bleach, water purifiers Zagros, Iran clear water purification, water treatment under the sink, under sink water filtration roben, water under the sink Robben, underground water, simple water purification, water purification strap, water treatment cream, water three, three-stage water treatment, water purification Japanese, Japanese water purifier, water purifier of transgenic
دیدگاه خود را ثبت کنید
تمایل دارید در گفتگوها شرکت کنید؟در گفتگو ها شرکت کنید.